상품명 | [ROB0153] 블랙 클레이디에터 트랙 섀시 로봇 플랫폼(Black Gladiator-Tracked Chassis) 검은 검투사 트랙 섀시 로봇 |
---|---|
상품요약정보 | Arduino 용 2WD 모바일 로봇 플랫폼은 표준 Arduino 마이크로 컨트롤러 와 함께 사용하기위한 작고 저렴한 모바일 플랫폼입니다 . 로봇은 두 개의 구동 모터, 바퀴 (및 후방 캐스터 볼), 프레임 및 모든 장착 하드웨어를 포함하는 키트로 제공됩니다 |
판매가 | 56,000원 |
제조사 | DFRobot |
원산지 | 해외 |
적립금 | 560원 (1%) |
상품코드 | P000BPCJ |
배송방법 | 택배 |
배송비 | 3,500원 (150,000원 이상 구매 시 무료) |
수량 |
SNS 상품홍보 | |
---|
(최소주문수량 1개 이상 / 최대주문수량 0개 이하)
사이즈 가이드수량을 선택해주세요.
위 옵션선택 박스를 선택하시면 아래에 상품이 추가됩니다.
상품명 | 상품수 | 가격 |
---|---|---|
[ROB0153] 블랙 클레이디에터 트랙 섀시 로봇 플랫폼(Black Gladiator-Tracked Chassis) 검은 검투사 트랙 섀시 로봇 | 56000 ( 560) | |
총 상품금액(수량) : 0 (0개) |
The track is made of engineering plastic that basically assured the good elasticity, excellent damping effect, and large road grip of the product. What’s more, it comes with two quality motors to provide high power and speed, which enables your DIY robot car to widely suit all kinds of road surfaces.
To explore more possibilities, you can use this tracked chassis with Arduino microcontrollers or add other electronic components on the base such as IR sensor, ultrasonic sensor, camera, LED, display, WIFI module, etc. For Arduino fans and smart robot car lovers, this is a good choice for you!
Note: the tracked chassis is unassembled, you need to get it done by yourself.
“Black Gladiator” Tracked Chassis Installation tutorial
Step 1: Install the load-bearing wheel (first install the M4*50 long screw into the load-bearing wheel), and lock the other side with the M4 screw.
Step2: place the gasket on the bracket and insert the load-bearing wheel into the hole of the bracket; the other end is also fitted with a gasket, which is also locked with the M4 nut. Be careful not to screw the load-bearing wheel too tightly.
Step 3: Insert the motor into the bracket and tighten it with 3 M3*6 flat head screws.
Step 4:Install the drive wheel: firstly insert the coupling into the drive wheel, and at the other end, use the allen key to fit the M3*8 hex socket screw into the drive wheel and lock it with the coupling.
Step 5:Install the drive wheel on the motor and tighten with black screw; please note: the hole on the coupling must be aligned with the flat end of the motor shaft.
Step 6: Remove the track first, remove the excess part of the track, and measure the required track length.
Embed the track pin into the track with a pair of pincers
How To Make DIY Arduino Traffic Sign Recognition Robot
How To Make DIY Arduino Bluetooth Controlled Robot At Home
More:
Terminator HK ~ Arduino & Raspberry Pi Robotics Project | 314Reactor
Black Gladiator-Tracked Chassis x1
상품의 사용후기를 적어주세요.
게시물이 없습니다
상품에 대해 궁금한 점을 해결해 드립니다.
게시물이 없습니다
고액결제의 경우 안전을 위해 카드사에서 확인전화를 드릴 수도 있습니다. 확인과정에서 도난 카드의 사용이나 타인 명의의 주문등
정상적인 주문이 아니라고 판단될 경우 임의로 주문을 보류 또는 취소할 수 있습니다.
무통장 입금은 상품 구매 대금은 PC뱅킹, 인터넷뱅킹, 텔레뱅킹 혹은 가까운 은행에서 직접 입금하시면 됩니다.
주문시 입력한 입금자명과 실제입금자의 성명이 반드시 일치하여야 하며, 7일 이내로 입금을 하셔야 하며 입금되지
않은 주문은 자동취소 됩니다.